back

As part of our ongoing commitment to customer safety, we hope you will find these guides a useful tool in ascertaining and problems you may come across from time to time when using a diamond blade.

If you encounter any issues when using a diamond blade the chances are you are cutting the wrong material for the blade. Also see selecting the correct blade for more help.


Blade Not Cutting

•Check that specification is correct for the material. Dull blades can be sharpened by cutting a soft abrasive material.
•Machine drive belts need retightening or the machine has insufficient horsepower for the specification being used.
•Check direction of rotation.

Core Cracks

•Excessive cutting pressure, caused by too high infeed results in the blade core bending and flexing. Metal fatigue will eventually cause core to crack.
•Worn shafts, damaged machine bearings, or blade incorrectly mounted.
•Blade too hard for the material being cut.

Damaged Arbor Hole

•Blade will hammer if it is incorrectly aligned when mounted. Make sure that the blade is mounted on the correct diameter spindle before tightening. Make sure that the pin holes slide over the drive pin.
•The blade will spin or vibrate on the spindle if the flanges are not properly tightened.
•The blade will pound if the saw shaft is badly worn or grooved.

Out of Round

•Blade shaft bearing may possibly be worn. Fit new bearing and ensure regular lubrication.
•Blade too hard for the material being cut, this will result in the blade hammering and wearing out of round. Choose a blade with a softer bond system.
•Machine spindle may have groove scored in it as result of previous blade slipping on spindle.

Over Heating

•Most common cause of blade failure. Overheating can cause many other problems such as core cracks, loss of tension, and segment loss. Overheating will usually cause black or bluish discolouration on the core.
•In wet cutting - inadequate water supply due to low water pressure, blocked or damaged water tubes or dust suppression systems being inadequate for wet cut blades.
•In dry cutting - excessive cutting pressure results in heat build up. Allow blade to do work. With hand held machines, use gentle reciprocating action and avoid cutting too deep in a single pass.

Rapid Wear

•Blade specification is causing the diamond to be over-exposed. Use a blade with a harder bond system.
•If the blade wears out of round this will increase the wear normally due to bad bearing, worn shaft or the blade specification being too hard for the material.
•An inadequate water supply can cause damaged or blocked water tubes
•Softening of the blade specification and low blade speed can be caused by loose drive belts.

Segment Cracks

•Use a blade with a softer bond system, as the blade specification may be too hard for the material being cut, causing hammering in the cut.

Segment Loss

•Blade has twisted or jammed in the cut because the material was not held firmly.
•Machine has been twisted or turned while blade is in the cut.
•Blade core has undercut due to cutting below the asphalt into the sub-base.
•Blade is too hard for the material being cut, resulting in the blade hammering in the cut.
•Blade is deflected in the cut due to the blade flanges being worn or deformed and failing to provide proper support.
•Inadequate water supply.

Tension Loss

•Blade core overheated. For wet cut blades ensure sufficient water supply.
•Check machine is running at correct rpm, that the flanges are of the correct and same size and that there is no wear on the machine bearing.
•The blade is deviating in the cut because it is too hard for the application.
•Ensure that the blade is not spinning on the spindle and that it is secure.
•Ensure that the blade is cutting in straight lines only.

Under Cutting

•Make sure that the blade specification has offset segments to assist removal of the slurry from the cut.
•Make sure that the blade is not cutting below the asphalt into the sub-base. Constant rubbing of the loose material causes premature wear and has no beneficial effect on the cut surface.
•Make sure that the water supply is correct as increased water flow will wash slurry from the contact area and reduce undercutting.

Uneven Segment Wear

•The effect of premature wear of the steel core is a particular problem in asphalt, fresh concrete and other highly abrasive materials. Segment loss may result from the steel core wearing to a knife edge just below the segment.
•Worn shafts, damaged machine bearings, or blade incorrectly mounted.
•Excessive cutting pressure, caused by too high infeed, results in the blade core bending and flexing. Metal fatigue will eventually cause the core to crack.
•Wet cutting - insufficient water.